ASTM A252 Grade 3
TUSPIPE supplies ASTM A252 Grade 3 pipes manufactured under the highest grade of the A252 standard. This certification ensures superior strength, allowing customers to build heavy-duty foundations with full confidence.
ASTM A252 Grade 3
ASTM A252 Grade 3 pipes are each used under different application circumstances. Welding processes are used to create the pipes. In the piling application, A252 Steel Piling Pipe is employed. The material is sturdy, corrosion-resistant, and resistant to wear and tear. Welded pipes are created using electric resistance welding, LSAW, and other welding techniques.
The chemical makeup of ASTM A252 Grade 3 Piling Pipe includes carbon, silicon, manganese, phosphorus, sulfur, and nitrogen. The pipes are used in water, gas, oil, construction, and piling activities to convey low-pressure liquids.
¿Por qué elegir tuspipe?
Desde 1998, Tianjin United Steel Piping Co., Ltd (TUSPIPE) se ha comprometido a suministrar tubos de línea de alta calidad.
Con más de 500.000 toneladas de capacidad de producción anual, la empresa presta servicio a diversos campos e industrias, como la explotación y transmisión de petróleo y gas, la construcción naval y de automóviles, el agua y la electricidad, la protección del medio ambiente, la ingeniería mecánica, la construcción de infraestructuras, etc.
TUSPIPE da mucha importancia a la calidad de los productos y a un riguroso control de calidad de los mismos. Para mantener la buena calidad de los productos, la empresa ha establecido un Centro de Pruebas e Inspección desde 2004. Con una serie de pruebas de última generación y equipos de inspección, el centro de pruebas e inspección es capaz de realizar las pruebas de tracción, pruebas hidráulicas, pruebas de impacto, DWTT, etc.
Applications of ASTM A252 Grade 3 Piling Pipe
ASTM A252 Grade 3 pipe piling is most commonly used for large-diameter applications. The cylindrical design of the pipe is ideal for bearing weight and can be used in a variety of settings, including buildings, retaining walls, and other structures. The pipe is also suitable for use in deep distances and at large diameters. The pipe is made from a variety of materials, including steel, concrete, and plastic. The pipe is also available in a variety of sizes and can be custom-made to meet the needs of the project. ASTM A252 Grade 3 pipe is an essential part of many projects, thanks to its ability to provide a stable base that meets international quality standards.
Specification of ASTM A252 Grade 3
| Estándar | A252 |
| Especificación | Welded Steel Pipe Piles |
| Tipo | Electric Resistance Welded (ERW) |
| Talla | NPS 1 TO NPS 24 [DN25 to DN 600], with nominal average wall thickness as given in ASME B 36.10M or as the customer’s requirement. |
| Diámetro exterior | 1-24 inches (33.4-609.6mm) |
| Thickness | 3-12mm |
| Longitud | Min 3 M, Max18 M, or according to the customer’s requirement. |
| Ends | Small sizes are plain, large sizes are beveled, or according to the customer’s requirement |
| Tratamiento de superficies | Normally bare or black varnish |
| Embalaje | Small sizes below 219.1mm in bundles, large sizes in bulk |
| Pruebas | Chemical Composition, Heat Analysis, Product Analysis, Tensile Requirements, etc. as customer’s requirements. |
Chemical Composition of ASTM A252 Grade 3 Steel Piling Pipe
When ordering ASTM A252 Grade 3 steel pipes, it is quite important to have a chemical analysis performed in order to ensure that the pipes meet the required specifications. The chemical analysis shall be performed in accordance with the test methods, practices, and terminology specified in ASTM A751. In order to verify that the pipes meet the required specifications, it is permissible for the buyer to make product analyses using 2 samples from each heat lot of pipe piles. By performing chemical analysis, the buyer can be assured that the steel pipes ordered will meet the necessary requirements.
Mechanical Properties of ASTM A252 Grade 3 Piling pipe
The ASTM A252 Grade 3 pipes must meet the tension requirements specified in the tables below. The yield point is the drop of the beam, the stop of the dial on the testing machine, the use of dividers, or other approved methods. If there is no definite yield point, determine the yield strength corresponding to a 0.2% permanent offset of the specimen’s gauge length or a 0.5% total extension under load. The method used to measure yield strength shall be recorded. Yield strength is measured in pounds per square inch (psi) and is expressed to the nearest 10 psi. If more than one test specimen is submitted, averages may be reported.
- Tensile Requirements
| NorE 1–Where an ellipsis (…) appears in this table, there is no requirement. | ||||
|---|---|---|---|---|
| Tensile strength, min, psi [MPa] | Grade 1 | Grade 2 | Grade 3 | |
| Yield point or yield strength, min, psi [MPa] | 50 000[345] | 60 000[415] | 60 000[455] | |
| Basic minimum elongation for nominal wall thicknesses % in. [7.9 mm] or more: | 30 000[205] | 35 000[240] | 45 000[310] | |
| Elongation in 8 in.[2032 mm] min, % | 18 | 14 | - | |
| Elongation in 2 in.[50.8 mm] min.% | 30 | 25 | 20 | |
| For nominal wall thicknesses less than 5/16 in.[7.9 mm], the deduction from the basic minimum elongation in 2 in. [50.8 mm] for each 1/32 – in.[0.8 mm] decrease in nominal wall thickness below 5/16 in. [7.9 mm], in percentage points | 1.5A | 1.25A | 1.0A | |
| A Table 2 gives the computed minimum values: | ||||
- Minimum Elongations
| Espesor nominal de la pared | Elongation in 2 in.[50.8mm],min,% | |||
|---|---|---|---|---|
| en. | mm | Grade 1 | Grade 2 | Grade 3 |
| 5/16 or 0.312 | 7.9 | 30.00 | 25.00 | 20.00 |
| 9/32 or 0.281 | 7.1 | 28.50 | 23.75 | 19.00 |
| 1/4 0r 0.250 | 6.4 | 27.00 | 22.50 | 18.00 |
| 7/32 or 0.219 | 5.6 | 25.50 | 21.25 | 17.00 |
| 3/16 or 0.188 | 4.8 | 24.00 | 20.00 | 16.00 |
| 11/64 or 0.172 | 4.4 | 23.25 | 19.50 | 15.50 |
| 5/32 or 0.156 | 4.0 | 22.50 | 18.75 | 15.00 |
| 9/64 or 0.141 | 3.6 | 21.75 | 18.25 | 14.50 |
| 1/8 or 0.125 | 3.2 | 21.00 | 17.50 | 14.00 |
| 7/64 or 0.109 | 2.8 | 20.25 | 16.75 | 13.50 |
| A The above table aives the calculated minimum elongaton values for varous nominal wall thicknesses. Where the specifed nomina wall thickness is intermediate to those shown above, the minimum elongation value shall be determined as follows: | ||||
| Grado | ||||
| 1 | E = 48t + 15.00[E = 1.90t +15.00] | |||
| 2 | E = 40t + 12.50[E = 1.56t +12.50] | |||
| 3 | E = 32t + 10.00[E = 1.25t +10.00] | |||
| where: | ||||
| E = elongation in 2 in..%and | ||||
| t = specofoed nominal wall thickness. in.[mm]. | ||||
Permissible Variations of ASTM A252 Steel Piling Pipes
| Artículo | Tolerancia |
|---|---|
| Peso unitario | +15%,-5% |
| Diámetro exterior | ±1% |
| Espesor de pared | ±12,5% |
- According to the standard, each length of ASTM A252 Grade 3 pipe pile must be weighed separately. The weight must not vary more than 15% over or 5% under its theoretical weight, which is calculated using the pipe’s length and weight per unit length. If the purchase order does not specify a weight, the manufacturer must ensure the pipe still conforms to this calculation formula.
- The outside diameter of pipe piles shall not deviate from the required outside diameter by more than 1%.
- At no point shall the wall thickness deviate by more than 12.5% below the nominal wall thickness.
