ASTM A500 Grade A
TUSPIPE offers ASTM A500 Grade A structural tubes that follow strict A500 standard requirements. Customers receive lightweight, reliable tubing suitable for everyday structural applications with guaranteed quality.
ASTM A500 Grade A
Les Société américaine pour les essais et les matériaux (ASTM) A500 steel grade is most commonly used in structural applications. This steel grade covers cold-formed welded and seamless carbon steel pipes used for construction purposes.
ASTM A500 Grade A is the lowest steel grade in ASTM A500 standard, and therefore it is the most common steel grade used in structural applications. It has good weldability and formability properties, as well as excellent strength properties. In addition, Grade A pipe is also suitable for high-temperature applications. For these reasons, Grade A is the steel grade of choice for many structural applications.
Pourquoi choisir tuspipe ?
Depuis 1998, Tianjin United Steel Piping Co., Ltd (TUSPIPE) s'engage à fournir des tubes de canalisation de haute qualité.
Avec une capacité de production annuelle de plus de 500 000 tonnes, l'entreprise dessert divers domaines et industries, tels que l'exploitation et la transmission du pétrole et du gaz, la construction navale et automobile, l'eau et l'électricité, la protection de l'environnement, l'ingénierie mécanique, la construction d'infrastructures, etc.
TUSPIPE accorde une grande importance à la qualité des produits et à leur contrôle rigoureux. Afin de maintenir une bonne qualité des produits, l'entreprise a mis en place un centre d'essai et d'inspection depuis 2004. Doté d'une série d'équipements d'essai et d'inspection de pointe, le centre d'essai et d'inspection est en mesure d'effectuer des essais de traction, des essais hydrauliques, des essais d'impact, des essais DWTT, etc.
ASTM A500 Grade A Square & Rectangle Tubing
The physical parameters necessary to fulfill the three classes of ASTM A500 Grade A square, rectangle, and special shaped tubing are listed below. A flattening test is not a standard requirement for A500 Grade A non-round tubing.
| Grade | Yield (min) | Tensile (min) | Elongation (min) |
|---|---|---|---|
| Gr. A | 39,000 psi | 45,000 psi | Determined by wall |
ASTM A500 Grade A Round Tubing
Below are the physical properties required to meet the three grades that we produce ASTM A500 Grade A round tubing. A flattening test is also a standard requirement for round tubing produced to the A500 Grade A.
| Grade | Yield(min) | Tensile (min) | Elongation (min) |
|---|---|---|---|
| Gr. A | 33,000 psi | 45,000 psi | Determined by wall |
Chemical Requirements of ASTM A500 Grade A
| Élément | Composition, % | |
|---|---|---|
| Heat analysis | Analyse des produits | |
| Carbone | 0.26 | 0.3 |
| Manganèse | 1.35 | 1.4 |
| Phosphore | 0.035 | 0.035 |
| Soufre | 0.035 | 0.045 |
| Cuivre | 0.2 | 0.18 |
Mechanical Properties of ASTM A500 Grade A Pipes
Physical Properties of ASTM A500 Grade A Pipes
| Propriétés physiques | Metric | Anglais | Comments |
|---|---|---|---|
| Densité | 7.80 g/cc | 0.282 lb/in³ | Typical of ASTM Steel |
Dimensions of ASTM A500 Grade A
Outside Diameter Specification:
- Round Tubes: Maximum outside diameter is 2235mm (88 inches) or less.
- Square/Rectangular Tubes: Measured at the 2-inch section, it should not deviate from the convexity/concavity tolerance.
Wall Thickness Specification:
- Maximum wall thickness should not exceed 25.4 mm (1 inch)
- The maximum wall thickness of welded tubing should not exceed 10% of the required wall thickness, excluding the weld seam.
Length Specification:
- Structural tubing may be in random/multiple/special lengths, compliance with length tolerance is required for specific lengths.
Straightness Specification:
- Permissible variation is 1/8 inch per foot.
Squareness of Sides Specification:
- Adjacent sides must be square (90°), with a maximum deviation of 62° permitted.
Outer Corner Radius Specification:
- Each outer corner radius should not exceed three times the required wall thickness.
Twist Specification:
- Adhere to the specified twist tolerances.
- Twist measurements should not be taken within two inches of the tubing’s ends.
