ASTM A500 Grade C
TUSPIPE provides ASTM A500 Grade C tubes meeting higher tensile requirements under A500 specifications. This ensures strong, stable, and consistent performance for modern steel structure projects.
ASTM A500 Grade C
Les ASTM A500 standard steel grade is commonly used in structural applications and construction. ASTM A500 Grade C steel is the most common steel grade used in round, square and rectangular Steel Tubes for structural applications.
It is general-purpose steel that can be welded, riveted, or bolted together to create a variety of shapes. Grade C steel is also often used in construction projects where it is common to see ASTM A500 Grade B steel grades being used as well. While both grades are widely available, Grade C steel is more affordable and thus a more popular choice for many construction projects.
Pourquoi choisir tuspipe ?
Depuis 1998, Tianjin United Steel Piping Co., Ltd (TUSPIPE) s'engage à fournir des tubes de canalisation de haute qualité.
Avec une capacité de production annuelle de plus de 500 000 tonnes, l'entreprise dessert divers domaines et industries, tels que l'exploitation et la transmission du pétrole et du gaz, la construction navale et automobile, l'eau et l'électricité, la protection de l'environnement, l'ingénierie mécanique, la construction d'infrastructures, etc.
TUSPIPE accorde une grande importance à la qualité des produits et à leur contrôle rigoureux. Afin de maintenir une bonne qualité des produits, l'entreprise a mis en place un centre d'essai et d'inspection depuis 2004. Doté d'une série d'équipements d'essai et d'inspection de pointe, le centre d'essai et d'inspection est en mesure d'effectuer des essais de traction, des essais hydrauliques, des essais d'impact, des essais DWTT, etc.
Chemical Requirements of ASTM A500 Grade C
| Élément | ASTM A500 Grade C |
|---|---|
| Analyse des produits | |
| Carbon, max | 0.27 |
| Manganese, max | 1.4 |
| Phosphore, max | 0.045 |
| Soufre, max | 0.045 |
| Copper, when copper steel is specified, min | 0.18 |
| a. ASTM A500 Grade C Properties for each reduction of 0.01 percentage point below the specified maximum for carbon, an increase of 0.06 percentage point above the specified maximum for manganese is permitted, up to a maximum of 1.50% by heat analysis and 1.60% by product analysis. | |
| b. If copper-containing steel is specified in the purchase order. | |
ASTM A500 Gr.C Carbon Steel Mechanical Properties
| ASTM A500 Gr. C properties | ||
|---|---|---|
| Épaisseur de la paroi | ±10% | |
| Squareness of Sides | 90°±2° | |
| External Corner Radius | R≤3WT | |
| Torsion | H≤38.1mm | ±1.3mm/1m length |
| 38.1mm＜H≤63.5mm | ±1.6mm/1m length | |
| 63.5mm＜H≤101.6mm | ±1.9mm/1m length | |
| 101.6mm＜H≤152.4mm | ±2.2mm/1m length | |
| 152.4mm＜H≤203.2mm | ±2.5mm/1m length | |
| H>203.2mm | ±2.8mm/1m length | |
| Rectitude | 10.4mm/1000mm in length | |
| Longueur | +50mm/-0mm | |
Tensile Requirements of ASTM A500 Grade C
| Round structural tubing | |
|---|---|
| Gr. C | |
| Tensile strength, min, psi (MPa) | 62,000 (425) |
| Yield strength, min, psi, (MPa) | 46,000 (315) |
| Elongation in 2 in. (50 mm), min, %D | 21C |
| Shaped structural tubing | |
|---|---|
| ASTM A500 Gr. C | |
| Tensile strength, min, psi (MPa) | 62,000 (425) |
| Yield strength, min, psi, (MPa) | 50,000 (345) |
| Elongation in 2 in. (50 mm), min, %D | 21C |
| a. Applies to specified wall thicknesses (t) equal to or greater than 0.120 in. (3.05 mm). For lighter specified wall thicknesses, the minimum elongation values shall be calculated by the formula: percent elongation in 2 in. (50mm) = 56t + 17.5, rounded to the nearest percent. For A500M use the following formula: 2.2t + 17.5, rounded to the nearest percent. | |
| b. Applies to specified wall thicknesses (t) equal to or greater than 0.180 in. (4.57 mm). For lighter specified wall thicknesses, the minimum elongation values shall be calculated by the formula: percent elongation in 2 in. (50 mm) = 61t + 12, rounded to the nearest percent. For A500M use the following formula: 2.4t + 12, rounded to the nearest percent. | |
| c. Applies to specified wall thicknesses (t) equal to or greater than 0.120 in. (3.05 mm). For lighter specified wall thicknesses, the minimum elongation values shall be by agreement with the manufacturer. | |
| d. The minimum elongation values specified apply only to tests performed prior to shipment of the tubing. | |
Permissible Variations in Dimensions of ASTM A500 Grade C
-Outside Dimensions of ASTM A500 Grade C Pipes
ASTM A500 Grade C Round Structural Tubing
The outside diameter shall not deviate more than 60.5 percent, rounded to the nearest 0.005 in. [0.1 mm], from the specified outside diameter for specified outside diameters of 1.900 in. [48 mm] and less, and 60.75 percent, rounded to the nearest 0.005 in. [0.1 mm], for specified outside diameters of 2.00in. [5 cm]. Outside diameter measurements must be made at a distance of at least two inches [five centimeters] from the tube ends.
ASTM A500 Grade C Square and Rectangular Structural Tubing
Outside dimensions, as measured across the flats at least 2in. [5cm] from the tube ends, should not depart from the necessary outside dimensions by more than the tolerance for convexity or concavity.
- Wall Thickness of ASTM A500 Grade C Pipes
At any point of measurement, the minimum wall thickness of the ASTM A500 Grade C tube shall not be less than 10% of the specified wall thickness. The maximum wall thickness of welded tubing shall not exceed 10% of the required wall thickness, excluding the weld seam.
Les spécifications relatives à l'épaisseur de la paroi des tubes carrés et rectangulaires doivent être appliquées entièrement au centre des méplats.
-Length of ASTM A500 Grade C Pipes
Les tubes structuraux sont souvent fabriqués en longueurs aléatoires de plus de 1,5 m, en longueurs multiples et en longueurs spéciales. Consulter la section 4. Lors de la commande de certaines longueurs, il est nécessaire de respecter la tolérance de longueur.
-Straightness of ASTM A500 Grade C Pipes
For ASTM A500 Grade C structural tubes, the permissible variation must be 1/8in. times the number of feet [10 mm times the number of meters] divided by 5.
-Squareness of Sides of ASTM A500 Grade C Pipes
The adjacent sides of ASTM A500 Grade C square and rectangular structural tubes must be square (90°), with a maximum deviation of 62° permitted.
-Radius of Corners of ASTM A500 Grade C Pipes
Chaque rayon d'angle extérieur d'un segment de tube structural carré ou rectangulaire ne doit pas dépasser trois fois l'épaisseur de paroi nécessaire.
-Twist of ASTM A500 Grade C Pipes
With ASTM A500 Grade C square and rectangular structural tube, the twist tolerances specified in the standard shall apply. Twist shall be determined by clamping one end of the tubing to a flat surface plate, measuring the height of each corner on the bottom side of the tubing above the surface plate near the opposite ends of the tubing, and calculating the twist (the difference in the heights of such corners), with the exception that for heavier sections, a suitable measuring device may be used to determine twist. Twist measurements must not be taken within two inches [five centimeters] of the tubing’s ends.
TUSPIPE ASTM A500 Grade C Marking
- The following information must be legibly inscribed on each length of ASTM A500 Grade C structural tubing: manufacturer’s name, brand, or trademark; specification designation (year of issuance is not necessary); and grade letter.
- The information given in (1) may be marked on a tag firmly connected to each bundle for ASTM A500 Grade C structural tubing with a specified outer diameter or big flat dimension of 4 in. [10 cm] or less.
- Codage à barres - Outre les normes visées aux points (1) et (2), le fabricant doit être en mesure d'utiliser le codage à barres comme moyen d'identification supplémentaire. Lorsqu'un bon de commande spécifie un certain système de codage à barres, ce système doit être utilisé.
NOTE - En l'absence d'un bon de commande spécifiant une méthode de codage à barres différente, il est suggéré que le codage à barres soit conforme à la norme B-1 de l'AIAG.
